Top fence company in fayetteville nc Secrets



Do it your own self fencing repair service could be a difficulty for the unskilled but it doesn't must be actually. Understanding times are tough and as a thirty year professional I will definitely make an effort to make fencing repair, changing rotted fencing messages as well as substituting panels in your fence workable for those that just like to do it your own self as well as save amount of money. I will certainly address:

* Do it Yourself Fencing Repair
* Changing rotted Fence Post
* Cedar fence Fence Blog post
* Treated Lumber Post
* Galvanized Metal Fence blog post
* Altering a Hardwood Fence Picket
* Including or Transforming Fence Rail

There are actually as many How to Wood Fence and Fencing Repair Work as there are actually nails in fence pickets. The manner in which I illustrate listed below has worked for me listed below in the Dallas Texas city region for several years.

Do it yourself fencing repair service: Is actually simple if you go about it properly however is quite difficult if you go about it the upside-down as well as can receive extremely frustrating and also costly.

Replacing Rotted Fence Message: Replacing blog posts in a Fence is among the hardest things about fencing repair service. I have observed DIYer's try every thing to acquire damaged fence blog post out of the ground. Some of my faves is what I phone the Grand Gulch. This is when a DIY is going to dig a gap thus significant around the fence article that they practically require a cement truck to introduce enough concrete to pack it. Have you ever dug an opening for a fence post? If therefore use the principle of excavating a 8 inch dimension hole for a fence article against the concrete of the outdated fence blog post regarding 2-2 1/2 feet deep-seated. After that take a sharp shooting trowel to clear a little bit of gunk from each edge of the concrete. Use post gap miner to get rid of the little bit of dirt that you released from the blog post hole. You today have a gap that is deeper sufficient that with a little bit of initiative you can make use of a rock club to lever the faulty message and also concrete right into the hole you only dug in order that it will be effortless to lift out.

Put the brand new post in the red, take the outdated hard concrete as well as make use of as filler in the red and put as much premixed moist concrete in the red as required to fill to the ground amount then plumb the post along with an amount. You can after that stand by 24 hours for the concrete to harden around the brand-new fence article the nail the fence panels to it or you can easily proceed catch the outdated or even brand new fence panels to it, re-level the post and after that use an old fence board to support it.

If you would like the easier way out then you can install a new fence post in next to the existing so that you do not have to dig the wood post out.

Cedar Fence Post: Cedar is naturally highly resistant to rot, decay, warping and bugs when used above ground. If it is saturated with moisture when installed in the hole with concrete around it and dries out, it will shrink leaving a void that will take on water. This creates a premature rotting process. This can also happen at the ground level if the concrete is not poured to a level that will help repel the water away from the fence post. You can use a good weather treatment to soak the post end prior to installing to extend the like of a cedar fence post. I have used Behr and Olympic with good success.

Treated Wood Post: Pressure treated wood post have a fence companies raleigh nc chemical that is resistant to rot and bugs. The tag on the end of the post at most retail chains like (Home Depot or Lowes) will tell you if it is good for ground contact. I have seen a lot of Landscape timbers used for posts in a fence. These usually do not have the proper treatment that will give it the rot protection so unless someone is on a very tight budget I will not recommend this type of wood post for fencing. Pressure treated pine fence post can warp or check from drying and shrinking (looks like a split). To minimize warping and twisting make sure that you attach the fence panels with the correct screws or nails. They need to be long enough to penetrate through the rail and the post by 2 1/2 - 3 inches. Also make sure that it is a Hot Dipped Galvanized screw or nail so that the chemicals in the wood do not deteriorate them.

I have seen that pressure treated wood post will last several years but can dry rot at the ground level but you can also minimize this by soaking the part that will come in contact with the ground in a good weather sealant.

Galvanized Metal Fence Post: Galvanized Metal Fence Post are my choice to use for fencing a backyard or changing out a rotted fence post. When they are installed correctly they can last a lifetime. Diameter of the hole they are to be cemented in to should be 8 - 10 inches and the depth should be a minimum of 30 inches and up to 48 inches. The type of soil and ground condition as well as the freeze line for your area will dictate this. They will cost a little more but in my opinion are worth the difference. Make sure that you get a heavy gauge like a. 095 and put a dome cap on it so that it doesn't act like a rain gauge. The appearance is not as natural as wood fence post but this can be easily by boxing it with a fence board or two.

Changing a Wood Fence Picket: Changing a Fence Picket is almost self explanatory. In the Dallas Texas metro the choices of fence pickets are starting with the best then to the last are Cedar (3-4 different grades), Composite (recycled materials like Trex, Correct Deck ), Pressure Treated Yellow Pine and Spruce - Fir - and White Pine (These are all in the white wood category). The white woods typically have a longevity of 7 - 10 years unless a good weather sealant is applied.

Once again make sure that your screws or nails are of the proper length and either hot dipped galvanized or aluminum.

You can attach a fence board to the top of the pickets or a nylon string to use to keep the top straight as you fasten them to the rails.

Adding or Changing Fence Rail: I have had the most success changing a fence rail by leaving the fence panel attached to the post. Use a sawzall with a metal cutting blade. Slip the blade in between the rail and the post so you can cut the nails or the screws. Use a Wonder Bar and a hammer so that you can wedge it between the rail and the fence board. Pry the fence board away from the fence rail. Follow the same procedure with all the fence boards. Take the fence rail out. Cut the new one to the same length. Drive the nails through the fence picket leaving the nail in. Insert the rail. Hammer to nails back into the fence rail. You then can use 3 1/2 inch hot dipped galvanized nail to hammer through the rail into the fence post.

Want to know more about Fencing Repair [http://www.fencesanddecksdallas.com] and look to see What Your Backyard can Become [http://www.fencesanddecksdallas.com]

The 2-Minute Rule for fence companies wilmington nc



Do it yourself fencing repair service may be a difficulty for the unskilled yet it doesn't have to be. Understanding opportunities are difficult and also as a thirty year expert I will definitely attempt to create fencing repair service, transforming deteriorated fencing posts and changing boards in your fence manageable for those that just like to carry out it yourself and save cash. I will certainly attend to:

* Do it Yourself Fencing Repair service
* Substituting deteriorated Fence Post
* Cedar fence Fence Article
* Treated Timber Article
* Galvanized Steel Fence article
* Modifying a Wood Fence Picket
* Adding or Transforming Fence Rail

There are actually as a lot of Just how to Hardwood Fence and Fencing Repair Work as there are nails in fence pickets. The manner in which I illustrate here has helped me below in the Dallas Texas region place for years.

Do it your own self fencing repair: Is very easy if you handle it properly but is extremely difficult if you deal with it the upside-down and also may receive very aggravating and expensive.

Switching Out Rotted Fence Article: Switching Out articles in a Fence is just one of the hardest features of fencing fixing. I have actually seen DIYer's try everything to get damaged fence message out of the ground. One of my favorites is what I contact the Grand Canyon. This is when a Do It Yourself will definitely dig an opening therefore significant around the fence article that they virtually require a cement truck to generate sufficient concrete to load it. Have you ever dug an opening for a fence post? If therefore utilize the idea of digging a 8 inch size opening for a fence message against the concrete of the aged fence message about 2-2 1/2 feet deep. Then take a sharp shooting trowel to get rid of a little bit of gunk apiece edge of the concrete. Make use of article opening digger to eliminate the bit of dust that you loosened up from the post hole. You today possess a gap that is actually deep-seated good enough that along with a little effort you can use a rock bar to lever the broken blog post and also concrete right into solitary confinement you merely dug to make sure that it will certainly be quick and easy to elevate out.

Place the brand-new pole in the hole, take the outdated challenging concrete and also usage as filler in the hole and put as a lot premixed moist concrete in the red as required to fill up to the ground level at that point plumb the rod along with a degree. You can easily then stand by twenty four hours for the concrete to solidify around the brand-new fence message the nail the fence panels to it or even you may proceed toenail the old or brand new fence doors to it, re-level the message and then use an old fence board to support it.

If you would like the easier way out then you can install a new fence post in next to the existing so that you do not have to dig the wood post out.

Cedar Fence Post: Cedar is naturally highly resistant to rot, decay, warping and bugs when used above ground. If it is saturated with moisture when installed in the hole with concrete around it and dries out, it will shrink leaving a void that will take on water. This creates a premature rotting process. This can also happen at the ground level if the concrete is not poured to a level that will help repel the water away from the fence post. You can use a good weather treatment to soak the post end prior to installing to extend the like of a cedar fence post. I have used Behr and Olympic with good success.

Treated Wood Post: Pressure treated wood post have a chemical that is resistant to rot and bugs. The tag on the end of the post at most retail chains like (Home Depot or Lowes) will tell you if it is good for ground contact. I have seen a lot of Landscape timbers used for posts in a fence. These usually do not have the proper treatment that will give it the rot protection so unless someone is on a very tight budget I will not recommend this type of wood post for fencing. Pressure treated pine fence post can warp or check from drying and shrinking (looks like a split). To minimize warping and twisting make sure that you attach the fence panels with the correct screws or nails. They need to be long enough to penetrate through the rail and the post by 2 1/2 - 3 inches. Also make sure that it is a Hot Dipped Galvanized screw or nail so that the chemicals in the wood do not deteriorate them.

I have seen that pressure treated wood post will last several years but can dry rot at the ground level but you can also minimize this by soaking the part that will come in contact with the ground in a good weather sealant.

Galvanized Metal Fence Post: Galvanized Metal Fence Post are my choice to use for fencing a backyard or changing out a rotted fence post. When they are installed correctly they can last a lifetime. Diameter of the hole they are to be cemented in to should be 8 - 10 inches and the depth should be a minimum of 30 inches and up to 48 inches. The type of soil and ground condition as well as the freeze line for your area will dictate this. They will cost a little more but in my opinion are worth the difference. Make sure that you get a heavy gauge like a. 095 and put a dome cap on it so that it doesn't act like a rain gauge. The appearance is not as natural as wood fence post but this can be easily by boxing it with a fence board or two.

Changing a Wood Fence Picket: Changing a Fence Picket is almost self explanatory. In the Dallas Texas metro the choices of fence pickets are starting with the best then to the last are Cedar (3-4 different grades), Composite (recycled materials like Trex, Correct Deck ), Pressure Treated Yellow Pine and Spruce - Fir - and White Pine (These are all in the white wood category). The white woods typically have a longevity of 7 - 10 years unless a good weather sealant is applied.

Once again make sure that your screws or nails are of the proper length and either hot dipped galvanized or aluminum.

You can attach a fence board to the top of the pickets or a nylon string to use to keep the top straight as you fence company raleigh fasten them to the rails.

Adding or Changing Fence Rail: I have had the most success changing a fence rail by leaving the fence panel attached to the post. Use a sawzall with a metal cutting blade. Slip the blade in between the rail and the post so you can cut the nails or the screws. Use a Wonder Bar and a hammer so that you can wedge it between the rail and the fence board. Pry the fence board away from the fence rail. Follow the same procedure with all the fence boards. Take the fence rail out. Cut the new one to the same length. Drive the nails through the fence picket leaving the nail in. Insert the rail. Hammer to nails back into the fence rail. You then can use 3 1/2 inch hot dipped galvanized nail to hammer through the rail into the fence post.

Want to know more about Fencing Repair [http://www.fencesanddecksdallas.com] and look to see What Your Backyard can Become [http://www.fencesanddecksdallas.com]

The fence companies raleigh nc Diaries



Do it your own self fencing repair could be an obstacle for the novice but it doesn't have to be. Understanding opportunities are difficult and also as a thirty year veteran I will definitely make an effort to make fencing repair work, transforming deteriorated fencing posts as well as switching out doors in your fence doable for those who such as to perform it on your own and also spare money. I will certainly attend to:

* Do it Yourself Fencing Repair service
* Substituting deteriorated Fence Post
* Cedar fence Fence Post
* Managed Lumber Article
* Galvanized Metallic Fence blog post
* Modifying a Wood Fence Picket
* Adding or Transforming Fence Rail

There are actually as a lot of How to Wood Fence and Fencing Repair Work as there are actually nails in fence pickets. The manner in which I define listed below has actually worked for me here in the Dallas Texas metro location for several years.

Do it on your own fencing repair work: Is effortless if you handle it properly yet is actually incredibly challenging if you go about it the wrong way and can get very aggravating and costly.

Changing Rotted Fence Message: Changing messages in a Fence is among the hardest aspects of fencing repair service. I have actually observed DIYer's try out every little thing to acquire defective fence blog post away from the ground. Some of my favorites is what I call the Grand Canyon. This is when a DIY will dig a gap thus major around the fence blog post that they just about need to have a concrete vehicle to produce adequate concrete to pack it. Possess you ever before dug an opening for a fence message? If therefore utilize the concept of digging a 8 inch diameter hole for a fence post versus the concrete of the outdated fence article regarding 2-2 1/2 feets deeper. After that take a sharp shooter shovel to clear a little gunk apiece edge of the concrete. Make use of article opening digger to get rid of the bit of dust that you loosened up from the post hole. You now have a gap that is actually deep-seated good enough that along with a little bit of initiative you can easily utilize a rock bar to lever the broken blog post and also concrete in to solitary confinement you merely dug to make sure that it will certainly be easy to elevate out.

Place the brand-new post in the hole, take the old hard concrete and also make use of as filler in the red as well as put as much premixed wet concrete in the red as needed to have to load to the ground degree then plumb the pole along with an amount. You can easily after that wait 24 hours for the concrete to solidify around the brand-new fence message the nail the fence panels to it or even you may proceed toenail the aged or new fence doors to it, re-level the article and after that use an old fence board to support it.

If you would like the easier way out then you can install a new fence post in next to the existing so that you do not have to dig the wood post out.

Cedar Fence Post: Cedar is naturally highly resistant to rot, decay, warping and bugs when used above ground. If it is saturated with moisture when installed in the hole with concrete around it and dries out, it will shrink leaving a void that will take on water. This creates a premature rotting process. This can also happen at the ground level if the concrete is not poured to a level that will help repel the water away from the fence post. You can use a good weather treatment to soak the post end prior to installing to extend the like of a cedar fence post. I have used Behr and Olympic with good success.

Treated Wood Post: Pressure treated wood post have a chemical that is resistant to rot and bugs. The tag on the end of the post at most retail chains like (Home Depot or Lowes) will tell you if it is good for ground contact. I have seen a lot of Landscape timbers used for posts in a fence. These usually do not have the proper treatment that will give it the rot protection so unless someone is on a very tight budget I will not recommend this type of wood post for fencing. Pressure treated pine fence post can warp or check from drying and shrinking (looks like a split). To minimize warping and twisting make sure that you attach the fence panels with the correct screws or nails. They need to be long enough to penetrate through the rail and the post by 2 1/2 - 3 inches. Also make sure that it is a Hot Dipped Galvanized screw or nail so that the chemicals in the wood do not deteriorate them.

I have seen that pressure treated wood post will last several years but can dry rot at the ground level but you can also minimize this by soaking the part that will come in contact with the ground in a good weather sealant.

Galvanized Metal Fence Post: Galvanized Metal Fence Post are my choice to use for fencing a backyard or changing out a rotted fence post. When they are installed correctly they can last a lifetime. Diameter of the hole they are to be cemented in to should be 8 - 10 inches and the depth should be a minimum of 30 inches and up to 48 inches. The type of soil and ground condition as well as the freeze line for your area will dictate this. They will cost a little more but in my opinion are durham fencing companies worth the difference. Make sure that you get a heavy gauge like a. 095 and put a dome cap on it so that it doesn't act like a rain gauge. The appearance is not as natural as wood fence post but this can be easily by boxing it with a fence board or two.

Changing a Wood Fence Picket: Changing a Fence Picket is almost self explanatory. In the Dallas Texas metro the choices of fence pickets are starting with the best then to the last are Cedar (3-4 different grades), Composite (recycled materials like Trex, Correct Deck ), Pressure Treated Yellow Pine and Spruce - Fir - and White Pine (These are all in the white wood category). The white woods typically have a longevity of 7 - 10 years unless a good weather sealant is applied.

Once again make sure that your screws or nails are of the proper length and either hot dipped galvanized or aluminum.

You can attach a fence board to the top of the pickets or a nylon string to use to keep the top straight as you fasten them to the rails.

Adding or Changing Fence Rail: I have had the most success changing a fence rail by leaving the fence panel attached to the post. Use a sawzall with a metal cutting blade. Slip the blade in between the rail and the post so you can cut the nails or the screws. Use a Wonder Bar and a hammer so that you can wedge it between the rail and the fence board. Pry the fence board away from the fence rail. Follow the same procedure with all the fence boards. Take the fence rail out. Cut the new one to the same length. Drive the nails through the fence picket leaving the nail in. Insert the rail. Hammer to nails back into the fence rail. You then can use 3 1/2 inch hot dipped galvanized nail to hammer through the rail into the fence post.

Want to know more about Fencing Repair [http://www.fencesanddecksdallas.com] and look to see What Your Backyard can Become [http://www.fencesanddecksdallas.com]

Fascination About fence company in fayetteville nc



Do it yourself fencing repair work may be a challenge for the inexperienced however it does not have to be. Recognizing times are tough and also as a thirty year pro I will try to create fencing repair service, modifying rotted fencing messages as well as substituting panels in your fence achievable for those who as if to carry out it your own self and conserve loan. I will definitely take care of:

* Do it Yourself Fencing Repair
* Changing decayed Fence Article
* Cedar fence Fence Blog post
* Handled Wood Message
* Galvanized Steel Fence message
* Transforming a Hardwood Fence Picket
* Adding or Changing Fence Rail

There are as a lot of How to Timber Fence as well as Fencing Repair Work as there are nails in fence pickets. The manner in which I define listed here has actually worked with me here in the Dallas Texas metro area for several years.

Do it on your own fencing repair work: Is very easy if you deal with it properly yet is actually incredibly hard if you go about it the wrong way and can obtain extremely discouraging as well as expensive.

Changing Rotted Fence Article: Switching Out articles in a Fence is just one of the hardest features of fencing repair service. I have actually observed DIYer's go every thing to receive defective fence blog post away from the ground. Some of my preferences is what I get in touch with the Grand Gulch. This is actually when a Do It Yourself will definitely dig an opening therefore significant around the fence article that they virtually require a cement truck to generate sufficient concrete to fill it. Have you ever dug a gap for a fence blog post? If thus make use of the principle of excavating a 8 inch size opening for a fence message against the concrete of the old fence post concerning 2-2 1/2 feets deep-seated. After that take a pointy shooter shovel to remove a little dirt from each side of the concrete. Use message opening digger to eliminate the bit of dust that you loosened up from the post hole. You today possess a gap that is actually deep-seated good enough that along with a little bit of initiative you can easily utilize a rock bar to lever the damaged post and also concrete in to solitary confinement you merely dug to make sure that it will certainly be simple to lift out.

Put the brand new rod in the red, take the aged tough concrete as well as use as filler in the hole and also placed as a lot premixed damp concrete in the hole as needed to fill to the ground level at that point plumb the rod along with a degree. You can then wait twenty four hours for the concrete to set around the brand-new fence message the nail the fence boards to it or you may go forward toenail the aged or new fence doors to it, re-level the blog post and after that use an old fence board to support it.

If you would like the easier way out then you can install a new fence post in next to the existing so that you do not have to dig the wood post out.

Cedar Fence Post: Cedar is naturally highly resistant to rot, decay, warping and bugs when used above ground. If it is saturated with moisture when installed in the hole with concrete around it and dries out, it will shrink leaving a void that will take on water. This creates a premature rotting process. This can also happen at the ground level if the concrete is not poured to a level that will help repel the water away from the fence post. You can use a good weather treatment to soak the post end prior to installing to extend the like of a cedar fence post. I have used Behr and Olympic with good success.

Treated Wood Post: Pressure treated wood post have a chemical that is resistant to rot and bugs. The tag on the end of the post at most retail chains like (Home Depot or Lowes) will tell you if it is good for ground contact. I have seen a lot of Landscape timbers used for posts in a fence. These usually do not have the proper treatment that will give it the rot protection so unless someone is on a very tight budget I will not recommend this type of wood post for fencing. Pressure treated pine fence post can warp or check from drying and shrinking (looks like a split). To minimize warping and twisting make sure that you attach the fence panels with the correct screws or nails. They need to be long enough to penetrate through the rail and the post by 2 1/2 - 3 inches. Also make sure that it is a Hot Dipped Galvanized screw or nail so that the chemicals in the wood do not deteriorate them.

I have seen that pressure treated wood post will last several years but can dry rot at the ground level but you can also minimize this by soaking the part that will come in contact with the ground in a good weather sealant.

Galvanized Metal Fence Post: Galvanized Metal Fence Post are my choice to use for fencing a backyard or changing out a rotted fence post. When they are installed correctly they can last a lifetime. Diameter fence companies wilmington nc of the hole they are to be cemented in to should be 8 - 10 inches and the depth should be a minimum of 30 inches and up to 48 inches. The type of soil and ground condition as well as the freeze line for your area will dictate this. They will cost a little more but in my opinion are worth the difference. Make sure that you get a heavy gauge like a. 095 and put a dome cap on it so that it doesn't act like a rain gauge. The appearance is not as natural as wood fence post but this can be easily by boxing it with a fence board or two.

Changing a Wood Fence Picket: Changing a Fence Picket is almost self explanatory. In the Dallas Texas metro the choices of fence pickets are starting with the best then to the last are Cedar (3-4 different grades), Composite (recycled materials like Trex, Correct Deck ), Pressure Treated Yellow Pine and Spruce - Fir - and White Pine (These are all in the white wood category). The white woods typically have a longevity of 7 - 10 years unless a good weather sealant is applied.

Once again make sure that your screws or nails are of the proper length and either hot dipped galvanized or aluminum.

You can attach a fence board to the top of the pickets or a nylon string to use to keep the top straight as you fasten them to the rails.

Adding or Changing Fence Rail: I have had the most success changing a fence rail by leaving the fence panel attached to the post. Use a sawzall with a metal cutting blade. Slip the blade in between the rail and the post so you can cut the nails or the screws. Use a Wonder Bar and a hammer so that you can wedge it between the rail and the fence board. Pry the fence board away from the fence rail. Follow the same procedure with all the fence boards. Take the fence rail out. Cut the new one to the same length. Drive the nails through the fence picket leaving the nail in. Insert the rail. Hammer to nails back into the fence rail. You then can use 3 1/2 inch hot dipped galvanized nail to hammer through the rail into the fence post.

Want to know more about Fencing Repair [http://www.fencesanddecksdallas.com] and look to see What Your Backyard can Become [http://www.fencesanddecksdallas.com]

Top fence company in fayetteville nc Secrets



Do it yourself fencing repair work could be a problem for the inexperienced however it does not must be. Understanding opportunities are tough and as a thirty year expert I are going to try to create fencing repair service, modifying rotted fencing articles and also substituting panels in your fence achievable for those that just like to do it on your own and also save cash. I will definitely take care of:

* Do it Yourself Fencing Repair
* Replacing decayed Fence Message
* Cedar fence Fence Article
* Handled Wood Post
* Galvanized Steel Fence article
* Transforming a Hardwood Fence Picket
* Adding or Altering Fence Rail

There are as several Just how to Wood Fence and Fencing Repair as there are nails in fence pickets. The way that I define right here has helped me below in the Dallas Texas city region for years.

Do it your own self fencing repair: Is quick and easy if you handle it properly yet is actually incredibly hard if you go about it the wrong way and can get extremely aggravating as well as expensive.

Switching Out Rotted Fence Article: Replacing posts in a Fence is one of the hardest things about fencing repair. I have seen DIYer's try everything to get broken fence post out of the ground. One of my favorites is what I call the Grand Canyon. This is actually when a DIY is going to dig a gap so big around the fence blog post that they just about need to have a concrete vehicle to produce adequate concrete to pack it. Possess you ever before dug an opening for a fence message? If therefore use the concept of digging a 8 inch diameter hole for a fence blog post versus the concrete of the outdated fence blog post concerning 2-2 1/2 feets deeper. After that take a sharp shooter shovel to remove a little dirt from each side of the concrete. Make use of blog post gap miner to take out the little of dust that you loosened up from the post hole. You now possess a gap that is actually deeper sufficient that with a little bit of initiative you can easily use a rock club to lever the defective article as well as concrete right into the hole you just dug so that it is going to be actually effortless to raise out.

Put the new pole in the red, take the outdated tough concrete as well as usage as filler in the hole and placed as a lot premixed damp concrete in the hole as needed to fill to the ground level at that point plumb the post with a level. You can then stand by 24-hour for the concrete to solidify around the brand-new fence post the nail the fence panels to it or even you can easily go on nail the old or even brand-new fence boards to it, re-level the post and then use an old fence board to support it.

If you would like the easier way out then you can install a new fence post in next to the existing so that you do not have to dig the wood post out.

Cedar Fence Post: Cedar is naturally highly resistant to rot, decay, warping and bugs when used above ground. If it is saturated with moisture when installed in the hole with concrete around it and dries out, it will shrink leaving a void that will take on water. This creates a premature rotting process. This can also happen at the ground level if the concrete is not poured to a level that will help repel the water away from the fence post. You can use a good weather treatment to soak the post end prior to installing to extend the like of a cedar fence post. I have used Behr and Olympic with good success.

Treated Wood Post: Pressure treated wood post have a chemical that is resistant to rot and bugs. The tag on the end of the post at most retail chains like (Home Depot or Lowes) will tell you if it is good for ground contact. I have seen a lot of Landscape timbers used for posts in a fence. These usually do not have the proper treatment that will give it the rot protection so unless someone is on a very tight budget I will not recommend this type of wood post for fencing. Pressure treated pine fence post can warp or check from drying and shrinking (looks like a split). To minimize warping and twisting make sure that you attach the fence panels with the correct screws or nails. They need to be long enough to penetrate through the rail and the post by 2 1/2 - 3 inches. Also make sure that it fence companies raleigh nc is a Hot Dipped Galvanized screw or nail so that the chemicals in the wood do not deteriorate them.

I have seen that pressure treated wood post will last several years but can dry rot at the ground level but you can also minimize this by soaking the part that will come in contact with the ground in a good weather sealant.

Galvanized Metal Fence Post: Galvanized Metal Fence Post are my choice to use for fencing a backyard or changing out a rotted fence post. When they are installed correctly they can last a lifetime. Diameter of the hole they are to be cemented in to should be 8 - 10 inches and the depth should be a minimum of 30 inches and up to 48 inches. The type of soil and ground condition as well as the freeze line for your area will dictate this. They will cost a little more but in my opinion are worth the difference. Make sure that you get a heavy gauge like a. 095 and put a dome cap on it so that it doesn't act like a rain gauge. The appearance is not as natural as wood fence post but this can be easily by boxing it with a fence board or two.

Changing a Wood Fence Picket: Changing a Fence Picket is almost self explanatory. In the Dallas Texas metro the choices of fence pickets are starting with the best then to the last are Cedar (3-4 different grades), Composite (recycled materials like Trex, Correct Deck ), Pressure Treated Yellow Pine and Spruce - Fir - and White Pine (These are all in the white wood category). The white woods typically have a longevity of 7 - 10 years unless a good weather sealant is applied.

Once again make sure that your screws or nails are of the proper length and either hot dipped galvanized or aluminum.

You can attach a fence board to the top of the pickets or a nylon string to use to keep the top straight as you fasten them to the rails.

Adding or Changing Fence Rail: I have had the most success changing a fence rail by leaving the fence panel attached to the post. Use a sawzall with a metal cutting blade. Slip the blade in between the rail and the post so you can cut the nails or the screws. Use a Wonder Bar and a hammer so that you can wedge it between the rail and the fence board. Pry the fence board away from the fence rail. Follow the same procedure with all the fence boards. Take the fence rail out. Cut the new one to the same length. Drive the nails through the fence picket leaving the nail in. Insert the rail. Hammer to nails back into the fence rail. You then can use 3 1/2 inch hot dipped galvanized nail to hammer through the rail into the fence post.

Want to know more about Fencing Repair [http://www.fencesanddecksdallas.com] and look to see What Your Backyard can Become [http://www.fencesanddecksdallas.com]

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15